Frigidaire dishwasher touchpad not working? Easy fix

As an Amazon affiliate, we earn a commision from qualifying purchases.

Are you having trouble with your Frigidaire dishwasher touchpad? If the touchpad is not responding or working properly, it can be frustrating and make it difficult to operate the dishwasher.

A malfunctioning touchpad can be caused by a variety of issues such as water finding its way to the control board, wiring problems, or even a simple software glitch.

In this article, we will discuss the possible reasons why your Frigidaire dishwasher touchpad is not working. We shall also provide you with the troubleshooting steps to fix the problem.

So, whether you’re a DIY enthusiast or just looking to save money on costly repairs, read on to learn how to get your Frigidaire dishwasher touchpad working again.

Frigidaire dishwasher touchpad not working

Here’s what you should do to get your Frigidaire dishwasher control panel up and working again…

Clean the dishwasher components

At times, your dishwasher is simply unresponsive due to debris being stuck in one part or the other of the dishwasher.

To begin with, clean the door latch assembly.

Here’s the thing, debris trapped inside the latch assembly might result in your dishwasher flashing lights and a frozen control panel.

Still on the same, it could be that some gunk has found its way into the UI pad or to the control board.

That being so, take out the touchpad and the control board.

If they are dirty, proceed to cleaning them using isopropyl alcohol or any other electronic contact cleaner and let the parts dry fully before reconnecting them.

Quick tip: you can use a toothbrush to scrub off any gunk that is not coming off.

Something else: water might have found its way to the control board.

If you note that this is the case with your dishwasher, take out the control board and air dry it.

Once you reconnect the board, make sure that your dishwasher’s touchpad is completely under the counter when the door is closed.

This should prevent the water from finding its way to the board again.

Inspect the wire connectors to the control board

Start by confirming that the two wire connectors between the control board and the touch screen are well inserted in place.

If not, remove and properly reconnect them.

Another thing, if any of the connectors has scorch marks, then, the connector is faulty and will require to be replaced.

If you opt to replace the wire harness, we recommend Frigidaire’s OEM dishwasher wire harness kit (you can order on Amazon).

Next, carefully inspect the ribbon cables connecting these wire connectors for hairline cracks.

Again, if any of the ribbon cables has cracks, it will need to be replaced.

Test the power supply within the dishwasher

Other times, it could simply be that your dishwasher is not getting enough power – typically, dishwashers require 120v AC.

Bearing that in mind, first confirm that the voltage from the power outlet is within this range.

If it’s not, connect your dishwasher to another working outlet and have an electrician have a look at the current outlet.

On the other hand, if the voltage is within the 120v AC range, proceed to testing the power at the control board.

For this, insert the probes into P3-5 (black) and P3-6 (white) – if you don’t get a reading of 120v AC, inspect for a loose connection within the unit.

For the most part, the neutral wire in Frigidaire dishwashers is notorious for working itself loose at the latch. So, be sure to check this out too.

On the other hand, if the voltage is okay, proceed to the test below…

Replace the touch pad

Other times, it could be that the touchpad has failed.

This might be due to a visible damage or an internal electrical fault.

Bearing that in mind, you will want to replace the panel as this might be the solution to getting your unit running again- we recommend Frigidaire’s OEM dishwasher touchpad (order the replacement part on Amazon).

Remember that OEM parts will fit well on your dishwasher and they generally outlive their generic counterparts.

Inspect the control board for signs of damage

Finally, it could be that your touchpad is not responding due to a faulty control board.

However, unlike other parts, there is no way to directly test the control board for faults.

Instead, you will need to rely on visual inspections.

Bearing that in mind, carefully inspect the board for scorch marks or any other marks that might point to a faulty board.

Quick tip: it would not hurt to reset your dishwasher before swapping out the board. To reset the dishwasher, simply unplug it from the power outlet and let it sit for five minutes.

If there are scorch marks around the capacitors (or the above steps do not fix your dishwasher), replacing the control board might be your only fix.

If you opt to go this way, we recommend Frigidaire’s OEM dishwasher control board – part #5304501595.


When to replace touchpad/control panel assembly on your Frigidaire dishwasher

So, how do you know that it is time to replace the touch pad?

Well, you might need to replace the touchpad if it exhibits any of the below signs:

  • It is unresponsive.
  • One or more of the buttons are not working.
  • It has some incorrect responses.
  • It is physically damaged.

However, before you decide to take this route, be sure to first troubleshoot for the steps we have outlined above.

After all, there is no need to swap out the control panel when it is not to blame or the problem can be easily resolved.

Frigidaire dishwasher touchpad not working – Frequently Asked Questions (FAQs)

How do I reset a Frigidaire dishwasher touchpad?

Since a dishwasher does not have a dedicated reset button, the easiest way to reset it is by unplugging it from the power outlet.

Then, let it sit for five minutes before you plug it back.

Why is my Frigidaire touchpad not working?

Several reasons might cause this such as:

  • Electrical glitches in the control board.
  • Faulty wire harness connections.
  • Water finding its way into the control board.
  • Dirty internal components.
  • Faulty wire ribbon connections.
  • The touchpad is faulty.
  • Faulty control board.

That being so, each of these problems has its own solution as we have seen above – refer to these solutions to quickly fix your panel.

Frigidaire dishwasher touchpad not working – final words

Remember that regular maintenance and care can go a long way in preventing issues like touchpad malfunctions from occurring in the first place.

So, always ensure the touchpad is fully beneath the counter – prevents water from coming in contact with the keypad or finding its way into the control board.


Frigidaire dishwasher control panel reset guide

Frigidaire dishwasher not starting lights blinking [FIXED]

How to enter diagnostic mode in Frigidaire dishwasher

Frigidaire gallery dishwasher error codes and how to fix them

Troubleshooting guide for Frigidaire professional dishwasher

Frigidaire gallery dishwasher troubleshooting guide

How to reset Frigidaire Gallery dishwasher

Leave a Comment