Maytag Bravos washer error codes, meaning, and recommended troubleshooting

We explain the meaning of the most common Maytag Bravos washer error codes to help you troubleshoot your washer fast in this guide..

Once you put your Maytag Bravos washer into diagnostic mode, the washer may display some fault codes depending on what has failed  (what you need to check).

Below is a list of the most common Maytag Bravos washer error codes to point you in the right direction when troubleshooting your Maytag Bravos washer

Maytag Bravos washer error codes – meaning and troubleshooting steps

Error code F0E2

Meaning: Oversuds detected and the washer is unable to fix the problem automatically

Recommended troubleshooting procedure

• Change to HE detergent (as recommended).
• Stop putting too much detergent- the issue can occur due to excessive detergent usage.
• Check the pressure hose connection (from tub to the main control)- you want to see if the hose is pinched/kinked/plugged/leaking air (and fix it depending on what you notice).
• Check the basket and the drive mechanism for mechanical friction (perhaps you’ll find some cloth items between the basket and the tub).

 

Error code F0E3

Meaning: Overloading detected (a load size bigger than the washer’s capacity detected OR basket cannot turn)

Recommended troubleshooting procedure

• Remove excess laundry and then restart the wash cycle.
• Check the basket and the drive mechanism for mechanical friction (perhaps you’ll find some cloth items between the basket and the tub).

 

Error code F0E4

Meaning: Spin limited fault due to the water temperature being too high for proper spin.

Recommended troubleshooting procedure

• Check if the water valve is functioning properly.

 

Error code F0E5 or “OFB”

Meaning: Off-balance load detected

Recommended troubleshooting procedure

• Redistributed items evenly manually.
• Check for possible weak suspension rods (basket won’t bounce up/down as it is supposed to if suspension is weak).

 

Error code F1E1

Meaning: Main Control fault.

Recommended troubleshooting procedure

Test and replace the main control (ACU), if needed

 

Error code F1E2

Meaning: There is a fault in the Main Control segment of main control (motor or drive system issues).

Recommended troubleshooting procedure

Inspect/test the wiring connection to the motor (and the motor) itself and repair. The motor or drive may need to be replaced.

 

More Maytag Bravos washer error codes

Error code F2E1

Meaning: UI Stuck Button (user interface is sensing a stuck button during Diagnostic Mode)

Recommended troubleshooting procedure

• Visually inspect ALL buttons and try to make any that appears stuck un-stuck.
• Run UI diagnostic Test Mode

 

Error code F2E3

Meaning: UI Mismatch (machine main control or the user interface part number do not match expected values)

Recommended troubleshooting procedure

Ensure compatible ACU and UI are installed- order correct part numbers.

 

Error code F2E4

Meaning: UI Software Error (Incompatible Parameter File)- a parameter file (in the UI) is incorrect.

Recommended troubleshooting procedure

Replace the entire UI.

 

Error code F2E5

Meaning: UI Software Error (invalid memory parameter)- a parameter file (in the UI) is corrupt

Recommended troubleshooting procedure

Replace the entire UI.

 

Error code F3E1

Meaning:  Pressure Fault (out-of-range pressure signal detected)

Recommended troubleshooting procedure

• Check the pressure hose connection (from tub to the main control)- you want to see if the hose is pinched/kinked/plugged/leaking air (and fix it depending on what you notice).
• Check water level sensing parts/components, especially the pressure transducer.

 

Error code F3E2

Meaning: Inlet water temp problem (inlet thermistor has been detected as open or shorted).

Recommended troubleshooting procedure

• Test temperature thermistor (measure the resistance-you want the values to be within the range below)

• Check hot and cold water valves- confirm if cold water as well as hot water is being dispensed.
• Replace the main control

Error code F4E1

Meaning: Heater is stuck ON(when it’s supposed to be OFF)

Recommended troubleshooting procedure

Test if the heater is operating properly- test the resistance of heater element (abnormal=infinity).

 

Error code F4E2

Meaning: When the heater is turned ON, it is not Turning On(the control is not able to detect the heater is turned ON)

Recommended troubleshooting procedure

Test if the heater is operating properly- test the resistance of heater element (abnormal=infinity).

 

Error code F5E1

Meaning: Lid switch fault (the lid is in lock state but the lid switch is opened).

Recommended troubleshooting procedure

• Perform Lid Lock test (under Service Test diagnostic Mode) and troubleshoot according to the error code
• Measure Lid Lock Resistance(and replace the lid lock if necessary)

 

Error code F5E2

Meaning: Lid Lock won’t lock or it has failed completely

Recommended troubleshooting procedure

• Check the lid for interference.
• Check for possible lock interference with the lid or the lock bezel.
• Also check if wash media buildup could be preventing lock bolt from properly extending.
• Perform Lid Lock test (under Service Test diagnostic Mode) and troubleshoot according to the error code
• Measure Lid Lock Resistance(and replace the lid lock if necessary)

 

Error code F5E3

Meaning: Lid lock won’t lock

Recommended troubleshooting procedure

• Excessive force on the lid is preventing the lock bolt from properly retracting so check if something is pressing the lid.
• Wash media buildup might be preventing the lock bolt from properly retracting so clear it.
• Perform Lid Lock test (under Service Test diagnostic Mode) and troubleshoot according to the error code
• Measure Lid Lock Resistance(and replace the lid lock if necessary)

 

Error code F5E4

Meaning: Lid was not opened between wash cycles.

Recommended troubleshooting procedure

• Perform Lid Lock test (under Service Test diagnostic Mode) and troubleshoot according to the error code
• Measure Lid Lock Resistance(and replace the lid lock if necessary)
• The main control may need to be replaced

 

Other Maytag Bravos washer error codes

Error code F6E3

Meaning: Communication Fault (communication error between the UI and ACU- UI not detected)

Recommended troubleshooting procedure

• Check UI harness for continuity.
• Check if there are stuck keys on UI and try to solve the problem
• Test the Main Control (ACU) and replace, if defective.

 

Error code F7E0

Meaning: Power loss detected

Recommended troubleshooting procedure

• Check power at the outlet.
• Check the circuit breakers, fuses, as well as junction box connections.
• Check the AC power cord (for continuity).
• Test the Main Control (ACU) and replace, if defective.

 

Error code  F7E1

Meaning: Power Fault (power lost during spin).

The washer is paused -for 5 minutes- to allow the basket stop before going on with the cycle

Recommended troubleshooting procedure

See error code F7E0 above

 

Error code  F7E2 / Error code  F7E3

Meaning: Motor Drive Module issue (main control has detected an Over Temp problem in the motor drive)

Recommended troubleshooting procedure

Test the wiring and all electrical connections (to the motor) and check the motor itself.

• Be sure to particularly check the following:
• Is the impeller turning freely? If impeller is not turning freely, determine what could be causing the mechanical friction/lockup
• Check motor resistance values (at the drive motor connector)
• Is the motor’s electrical connection cover fully seated- Visually check if the clips are actually fully seated.
• Sometimes you may need to replace the drive.

 

Error code F7E4

Meaning: Motor drive module over-voltage fault

Recommended troubleshooting procedure

See error code  F7E2 / error code  F7E3 above

 

Error code F7E6

Meaning: Motor circuit fault (loss of phase)- one or more phase lines open

Recommended troubleshooting procedure

• Check the drive system for problems.
• Inspect the entire motor circuit. Also check the motor itself (See error code F7E2 / error code  F7E3).

 

Error code  F7E7

Meaning: Motor start failure (main control cannot get to the needed motor speed)

Recommended troubleshooting procedure

• Check for mechanical friction on the drive mechanism or the basket (remove any items between the basket and tub).
• Ensure items are distributed evenly (this can be caused by an off balance load).
• Check the drive system for problems. Also check the motor itself (See error code F7E2 / error code  F7E3).

 

Error code F7E8

Meaning: Motor Stator Fault (over temperature condition) – motor temperature too high.

Recommended troubleshooting procedure

• Perform service calibration afresh to calibrate the water level as well as load size detection.
• Check for mechanical friction on the drive mechanism or the basket (remove any items between the basket and tub)

 

Error code F7E9

Meaning: Locked rotor (motor not moving when it’s being actively driven)

Recommended troubleshooting procedure

• Check for mechanical friction on the drive mechanism or the basket (remove any items between the basket and tub)
• See error code F7E2 / error code  F7E3).

 

Error code “LF”/ Error code F8E1

Meaning: Long Fill

Recommended troubleshooting procedure

Check for the following:

• Is the water supply actually connected and fully turned on?
• Are the hose screens plugged?
• Is some water dripping out of drain hose?
• Is the drain hose installed as it should?
• Is the water pressure too low (fill times will typically be longer than ten minutes if this is the case).
• Is pressure hose connection -from tub to main control- kinked, plugged, pinched, or leaking air?
• Are both cold and hot water valves dispensing water?

 

Error code F8E3

Meaning: Overflow OR flood condition (water level exceeds washer capacity)

Recommended troubleshooting procedure

Check for the following:

• Is pressure hose connection -from tub to main control- kinked, plugged, pinched, or leaking air?
• Is the drain hose installed as it should?
• Troubleshoot the cold and hot water valves – test the electrical connections (to the valves) and check the valves themselves (the valve coils might have stopped working)
• Check the pressure transducer (on main control) –it may have failed

 

Error code F8E5

Meaning: Hot, cold inlets reversed

Recommended troubleshooting procedure

• Connect the inlet hoses correctly.
• Test temperature thermistor (see error code F3E2)
• Troubleshoot the cold and hot water valves – test the electrical connections (to the valves) and check the valves themselves (the valve coils might have stopped working)

 

Error code F8E6

Meaning: Water hazard (water sensed in the tub or lid left open for 10 or more minutes)

Recommended troubleshooting procedure

• See error code F8E3 above
• Troubleshoot the lid lock as under Error code F5E1

 

Error code “drn” or “dr” or F9E1

Meaning: Drain pump fault (causing long drain issue)

Recommended troubleshooting procedure

Check for the following:

• Is drain hose clogged?
• Is the drain pump itself clogged?
• Is drain hose height more than 8”(2.4m)?
• Is pressure hose connection -from tub to main control- kinked, plugged, pinched, or leaking air?
• Is the too much detergent in the machine?
• Is the drain pump really pumping water? Check and replace, if faulty.

 

Error code F9E2

Meaning: Water Ring Fault (system unable to fully drain water from the load).

Recommended troubleshooting procedure

See error code “drn” or “dr” or F9E1 above

 

How to clear Maytag Bravos washer error codes

To clear saved fault codes, put it into Service Diagnostic mode.

Now press and then hold the third (3^rd) button you used to get into Service Diagnostic mode – hold it for 5 seconds.

Once the saved fault codes are erased, the display will immediately show “888” – a beep will also sound.

 

Final words

Remember that to view these Maytag Bravos washer error codes, you need to put your washer into diagnostic mode.

It’s also important to note that some Maytag Bravos washer error codes will usually stop the appliance if you’re attempting to run a service diagnostics verification cycle (it will only complete the cycle after you fix the cause of the fault code).

One final thing: Try to retrieve your washer’s the tech sheet from inside the washer (you have to raise the washer’s top panel to access it).

It will describe all specific Maytag Bravos washer fault codes that apply for your model in detail including the needed tests for the various parts so it will be very handy during your troubleshooting process.

ALSO READ:

How to reset Maytag Bravos washer (Steps and tips)

Maytag Bravos MCT washer diagnostic mode (How to enter)

Maytag washing machine cycle times and descriptions