Whirlpool top load washer error codes and Maytag top load washer error codes

Both Whirlpool and Maytag top load washers are pretty much similar so this Whirlpool top load washer error codes guide can be helpful to those looking for the meaning of various Maytag top load washer error codes (Fact: Whirlpool bought Maytag in 2006).

Having clarified that, below is a Whirlpool top load washer error codes list (error description and what to check) to point you in the right direction when you’re fixing your Whirlpool top load washer (or Maytag top load washer).

Whirlpool top load washer error codes and Maytag top load washer error codes -error meaning and potential fixes

Please note that this may not cover all Whirlpool top load washer error codes/ Maytag top load washer error codes because some error codes appear only on selected top loading models.

For that reason, consult your owner’s manual for a complete list of error codes specific to your model.

LOC or LC error code

Error description

Control Lock activated

Potential solution

Touch Control Lock button (In some models, you press and hold this button).

 

dET error code

Error description

Detergent cartridge was not detected in washer dispenser

Potential solution

Check if dispenser cartridge is correctly inserted and dispenser drawer shut completely.

Ignore the error if you’re using single-load detergent doses

 

Int error code

Error description

Cycle was paused/canceled

Potential solution

The washer could take 20 – 30 minutes to finish spinning and drain- The error code may be shown during that time.

To clear the code, press pause/cancel button twice then the power button once.

If the code persists, reset washer (to reset, just unplug it or disconnect power for about one minute).

 

Error code rL or F34

Error description

Some items detected in washer during a Clean Washer cycle.

Potential solution

Remove items (from the drum) then restart Clean Washer cycle.

 

Error code Sud or Sd

Error description

Excessive sudsing detected in washer

Potential solution

The washer will try to eliminate excess suds so wait. 

Important: Be sure to use HE detergent (recommended amount).

Where “no splash” (or “easy-pour” liquid chlorine bleach) was used, run the washing machine with normal liquid bleach products.

Finally, the code could be caused by a restricted drain hose -or standpipe(drainpipe) so check the drain hose for clogging or kinks.

 

Error code F5 E2

Error description

Door not locking properly

Potential solution

Remove any items obstructing the door.

Clear code as explained in error code Int

 

Error code F7 E1

Error description

Motor speed sensing fault -the motor cannot get to the required speed (for cycle selection).

Potential solution

• Remove all shipping bolts
• Ensure washer is not overloaded

Clear code as explained in error code Int

 

Error code F8 E1 or error LO FL

Error description

The washer is detecting low water flow.

Potential solution

Ensure water supply is actually turned on -both cold and hot water faucets/valves should be fully open.

Check water inlet hoses for kinking and remove any kinks.

Remove any anti-flood hoses (and controls) in the water supply line connected to your washer

Clear code as explained in error code Int

 

Error code F8 E2

Error description

Dispenser system problem

Potential solution

Check detergent drawer (or detergent cartridge) for clogging (it can be logged with detergent).

 

Error code F9 E1

Error description

Drain times are unusually longer ( typically over eight minutes).

Potential solution

Check drain hose for kinking or clogging (Use U shaped drain hose form on drain hose) 

Note that standpipe(drainpipe) height requirements are maximum: 96″(244 cm) and minimum: 39″(99 cm).

Also check for excessive suds –resolve as indicated in error code Sud or Sd

 

Other F# E# format error codes

Error description

Indicates other error(s)

Potential solution

Reset washer.

Re-select the wash cycle and again press Start.

If the code won’t clear, see your washer’s tech sheet for further troubleshooting.

 

More whirlpool top loading washing machine error codes (other Maytag top loading washing machine error codes)

Error Code drn

Error description

Washer not draining properly

Potential solution

Check for drain hose installation problem- and install it properly.

 

F# E# or F## format error

Error description

System error

Potential solution

Press START/PAUSE one time to clear the error code then press “START/PAUSE” once more to restart washer.

 

HC error code

Error description

Hot -cold inlet hoses swapped (reversed).

Potential solution

Interchange the hoses (make sure they’re installed correctly). 

 

LdL error code

Error description

Lid is unable to lock

Potential solution

Check for an item (in the load- under the lid) that could be preventing the lid from properly locking and remove it.

Check for detergent buildup (around the lid locking mechanism) and clear it.

 

LdU error code

Error description

Lid is not able to unlock

Potential solution

Check and remove objects on the washer lid keeping it from un-locking. Things (like basket of laundry) should be removed from top of washer.

 

Lo FL, LF,  or F8 E1 Error codes

Error description

The machine is taking longer to fill.

Potential solution

Check for possible issues in water supply (to the washing machine). In essence, ensure hot as well as cold water faucets have been turned on fully.

Note: Both Cold and Hot water need to be supplied to your washer.

 

lid Error Code

Error description

Lid left open.

Potential solution

Close the lid.

 

Ofb Error Code

Error description

Out of balance load

Potential solution

Don’t touch the washer – it is running an automatic load-balance correction routine (so just wait)

But you can try these steps depending on your situation:

• If dial is flashing and washer has stopped, manually redistribute the load then close the lid then press START/PAUSE. 
• If you’re experiencing some vibration (during spinning) or washer has stopped (with every dial light flashing), reload laundry evenly (in loose heaps) around the washplate.

If dial is flashing, manually redistribute the load then close the lid then press START/PAUSE

 

OL error code

Error description

Washer is overloaded

Potential solution

Remove a few items to correct the overload then add HE detergent then close lid then press START/PAUSE

 

PF error code

Error description

Wash cycle interrupted due to a power failure.

Potential solution

Touch then hold START to re-start the cycle or press “POWER” to clear display.

 

How to view the above Whirlpool top load washer error codes / Maytag top load washer error codes

You should start a diagnostic test mode on your washer to find these errors.

Needless to say, you begin the diagnostic test modes in different ways (it all depends on the top washer model you have).

But to give you a solid idea about starting Whirlpool top load washer diagnostic mode, we recommend you watch this YouTube video.

 

Final words

Please remember these while the above whirlpool top load washer diagnostic codes won’t troubleshoot the washer for you, they will put you on the right track and help you close in on the component or area of the washer causing the problem.

This is perhaps the best trick you can use to narrow down on the trouble-causing part/section when it comes to troubleshooting these types of washers.

Over to you!

ALSO READ:

How to reset whirlpool front loader washer step-by-step

Whirlpool Cabrio Washer diagnostic test – how to enter diagnostic mode

Maytag centennial washer troubleshooting (fixes and tricks

Maytag Washer Door Lock Problem [Fixed